|
The 6332M board card cannot be reset
|
|
0
|
253
|
April 1, 2021
|
|
For the RDworks V8 software.After change the idle acceleration in the cutting parameters of the user parameters,writting parameters is invalid
|
|
0
|
337
|
April 1, 2021
|
|
Press Z- or Z+for a long time(about 3~4s),the Z axis will always go down/up;Press the short time is noraml
|
|
0
|
279
|
April 1, 2021
|
|
How to install the USB drive
|
|
0
|
426
|
March 31, 2021
|
|
CCD software "take pictures in advance" problem
|
|
0
|
255
|
March 31, 2021
|
|
The floodlight of the camera is not bright
|
|
0
|
280
|
March 31, 2021
|
|
Incompatible flie formats
|
|
0
|
285
|
March 31, 2021
|
|
The scanned figure is uneven at the bottom
|
|
0
|
299
|
March 31, 2021
|
|
"Flie incompatibility" in RDC6442
|
|
0
|
284
|
March 31, 2021
|
|
The problem with the parameters setting for V6342
|
|
0
|
268
|
March 30, 2021
|
|
The depth of cutting or engrving is not enough
|
|
0
|
303
|
March 30, 2021
|
|
The bottom is uneven when carving
|
|
0
|
267
|
March 30, 2021
|
|
When starting the reset,the shaft has been touching the voltage limit switch
|
|
0
|
303
|
March 30, 2021
|
|
Do not know how to upgrade file
|
|
0
|
260
|
March 30, 2021
|
|
The panel cannot cnnnect to the device
|
|
0
|
270
|
March 30, 2021
|
|
Trying to cut a squre results in a parallelogram
|
|
0
|
265
|
March 30, 2021
|
|
Can not cut through the object to be cut
|
|
0
|
286
|
March 30, 2021
|
|
Draw a 20X20 retangle in V8,change it to a 20X30 rectangle,press ESC,the shape is gone
|
|
0
|
273
|
March 30, 2021
|
|
Out2 and wind connected to 2W/80mA solenoid valve does not work
|
|
0
|
296
|
March 30, 2021
|
|
Text is missing when a file edited with CorelDraw X4 is imported into RDWorksv8setup (8.0.22)
|
|
0
|
269
|
March 30, 2021
|
|
Graphics in software and actual graphics left and right or upside down
|
|
0
|
266
|
March 30, 2021
|
|
Laser is emitted when working, and no laser is emitted when shooting
|
|
0
|
277
|
March 30, 2021
|
|
When the reset is started,the X axis stops after touching the limit switch,while the Y axis is still running very slowly
|
|
0
|
310
|
March 30, 2021
|
|
When the boot panel can not load,no cuisor flashing,black screen
|
|
0
|
235
|
March 30, 2021
|
|
The panel is stuck at runtime
|
|
0
|
303
|
March 30, 2021
|
|
Use a servo drive.The circle cutting is not closed,the line is not straight and the X,Y axis jitter
|
|
0
|
266
|
March 30, 2021
|
|
After correcting the cut cross,the cut cross is not even,or has deviation
|
|
0
|
275
|
March 30, 2021
|
|
How to set the cutting starting point and direction
|
|
0
|
294
|
March 30, 2021
|
|
Do not know how to adjust the Z-axis step
|
|
0
|
300
|
March 30, 2021
|
|
The panel indicates that the machine is protected after cilck the start
|
|
0
|
279
|
March 30, 2021
|