Anchor point is useless
|
|
0
|
224
|
April 5, 2021
|
The cutting pattern is not closed or the light is uneven
|
|
0
|
232
|
April 5, 2021
|
The docking position of the laser head is not at the positioning point after the work is completed
|
|
0
|
238
|
April 5, 2021
|
The starting point of the cutting figure is not at the anchor point
|
|
0
|
191
|
April 5, 2021
|
The cutting figure is different from the actual figure size
|
|
0
|
215
|
April 5, 2021
|
USB connection is not available (there is a port COM)
|
|
0
|
238
|
April 5, 2021
|
The laser keeps emitting light
|
|
0
|
239
|
April 5, 2021
|
No light during laser processing
|
|
0
|
240
|
April 5, 2021
|
XY axis limit does not work
|
|
0
|
267
|
April 5, 2021
|
Unable to control XY axis movement
|
|
0
|
229
|
April 5, 2021
|
XY axis does not move when reset
|
|
0
|
248
|
April 5, 2021
|
The power-on reset is normal, and the voltage is normal. When you press the focus button, the laser head is in the focus position after falling and hitting the board and does not go to the stage
|
|
0
|
242
|
April 5, 2021
|
Switch to manual mode, press the Z+, Z- buttons on the operation panel, Z Shaft motor does not move
|
|
0
|
209
|
April 5, 2021
|
After the system has been working for a long time, When the cutting head is in the following state, overshoot Or severe jitter
|
|
0
|
208
|
April 5, 2021
|
After noraml connection,pressing the auto-focus button and the cutting head will move upward all the time
|
|
0
|
256
|
April 5, 2021
|
The cutting head moves download while auto-focusing or following
|
|
0
|
256
|
April 5, 2021
|
Cutting head is not up and down,but the motor has sound
|
|
0
|
228
|
April 5, 2021
|
Press the test key ".",the cutting head is in the following state,but the jitter is large
|
|
0
|
240
|
April 5, 2021
|
The cutting head cannot be controlled,and the indicator light of the level adjuster does not flicker
|
|
0
|
234
|
April 5, 2021
|
When the cutting head works,sometimes it can be lowered,sometimes it caannot be lowed
|
|
0
|
207
|
April 5, 2021
|
The cutting head is always up in automatic mode
|
|
0
|
260
|
April 5, 2021
|
Press the automatic focus,the laser head slowly moves down,after touching the plate,it stops at the focus position without lifting
|
|
0
|
239
|
April 5, 2021
|
When pressing the test key,the laser head cannot rise and fall normally
|
|
0
|
239
|
April 5, 2021
|
Auto-focus problem for follow-up cutting
|
|
0
|
229
|
April 5, 2021
|
Introduction line of Metalcut software
|
|
0
|
221
|
April 5, 2021
|
The laser head position displays on the software is inconsistent with reality
|
|
0
|
224
|
April 5, 2021
|
RDC6332M cannot auto-focus
|
|
0
|
235
|
April 1, 2021
|
RDC6332M,the mixing cutting head does not move when starting
|
|
0
|
232
|
April 1, 2021
|
The auto chunking of the RDC6442S doesn't work
|
|
0
|
245
|
April 1, 2021
|
The 6442 board gets stuck when entering files in processing mode or scanning mode
|
|
0
|
226
|
April 1, 2021
|