|
About the FAQ category
|
|
0
|
298
|
February 12, 2021
|
|
Cutting will cause problems in the picture
|
|
0
|
356
|
April 20, 2021
|
|
Replace a large wattage machine
|
|
0
|
328
|
April 20, 2021
|
|
Ruida controller can not reset automaticlly when power on
|
|
0
|
392
|
April 19, 2021
|
|
Z axis does not work in RDC6445G
|
|
0
|
569
|
April 19, 2021
|
|
I bought 6442S instead of 6445G, what should I do if the XY axis direction is reversed
|
|
0
|
381
|
April 19, 2021
|
|
Password of Ruida mainboard
|
|
0
|
583
|
April 19, 2021
|
|
Can the 6445 panel be used with the 6442S motherboard
|
|
0
|
369
|
April 17, 2021
|
|
HYZ100 power supply is connected with 6445G, why there is no display on the panel
|
|
0
|
380
|
April 17, 2021
|
|
The X axis of the main control board RDLC320-A does not work, how to troubleshoot
|
|
0
|
382
|
April 16, 2021
|
|
How to prove that the 24v port of the CN1 interface of the controller can work normally
|
|
0
|
347
|
April 16, 2021
|
|
The L and P indicators on the power supply are both off. Is it broken
|
|
0
|
350
|
April 16, 2021
|
|
MYJG150W, everything is normal, all connections are correct, but if you try to make a complete grating engraving, even if the power is reduced to a minimum, it will become too deep and can only be cut
|
|
0
|
348
|
April 16, 2021
|
|
The power supply device makes a huge noise and malfunctions and causes the laser to emit (pulse) by itself, which is very dangerous. It can also work when the power is turned on. Power DY13
|
|
0
|
385
|
April 16, 2021
|
|
Continuous discharge of power supply
|
|
0
|
377
|
April 16, 2021
|
|
Need a laser tube in which a transparent window is installed instead of a resonator mirror
|
|
0
|
330
|
April 16, 2021
|
|
The laser tube emits pink light, no output, and it is impossible to mark the paper in front of the light outlet. Is this laser tube broken?
|
|
0
|
345
|
April 16, 2021
|
|
Low frequency use of laser tubes in cold areas
|
|
0
|
365
|
April 16, 2021
|
|
The laser is not engraved, but the laser beam can be seen on the back. How can I solve it?
|
|
0
|
410
|
April 16, 2021
|
|
CR35 laser tube light flickers very frequently
|
|
0
|
311
|
April 16, 2021
|
|
Don't know how to encrypt the motherboard
|
|
0
|
373
|
April 5, 2021
|
|
Invalid layer sort
|
|
0
|
290
|
April 5, 2021
|
|
Setting the cutting point is invalid
|
|
0
|
346
|
April 5, 2021
|
|
Invalid process number arrangement
|
|
0
|
305
|
April 5, 2021
|
|
Z axis is not working properly
|
|
0
|
394
|
April 5, 2021
|
|
The laser light is weak and cannot be controlled
|
|
0
|
345
|
April 5, 2021
|
|
Dislocation of cutting graphics
|
|
0
|
314
|
April 5, 2021
|
|
Can't read the USB flash drive
|
|
0
|
372
|
April 5, 2021
|
|
The time on the control panel is wrong
|
|
0
|
326
|
April 5, 2021
|
|
No display on control panel
|
|
0
|
367
|
April 5, 2021
|