|
Cutting head is not up and down,but the motor has sound
|
|
0
|
264
|
April 5, 2021
|
|
Press the test key ".",the cutting head is in the following state,but the jitter is large
|
|
0
|
278
|
April 5, 2021
|
|
The cutting head cannot be controlled,and the indicator light of the level adjuster does not flicker
|
|
0
|
275
|
April 5, 2021
|
|
When the cutting head works,sometimes it can be lowered,sometimes it caannot be lowed
|
|
0
|
238
|
April 5, 2021
|
|
The cutting head is always up in automatic mode
|
|
0
|
303
|
April 5, 2021
|
|
Press the automatic focus,the laser head slowly moves down,after touching the plate,it stops at the focus position without lifting
|
|
0
|
274
|
April 5, 2021
|
|
When pressing the test key,the laser head cannot rise and fall normally
|
|
0
|
279
|
April 5, 2021
|
|
Auto-focus problem for follow-up cutting
|
|
0
|
265
|
April 5, 2021
|
|
Introduction line of Metalcut software
|
|
0
|
250
|
April 5, 2021
|
|
The laser head position displays on the software is inconsistent with reality
|
|
0
|
258
|
April 5, 2021
|
|
RDC6332M cannot auto-focus
|
|
0
|
271
|
April 1, 2021
|
|
RDC6332M,the mixing cutting head does not move when starting
|
|
0
|
268
|
April 1, 2021
|
|
The auto chunking of the RDC6442S doesn't work
|
|
0
|
295
|
April 1, 2021
|
|
The 6442 board gets stuck when entering files in processing mode or scanning mode
|
|
0
|
261
|
April 1, 2021
|
|
The 6332M board card cannot be reset
|
|
0
|
249
|
April 1, 2021
|
|
For the RDworks V8 software.After change the idle acceleration in the cutting parameters of the user parameters,writting parameters is invalid
|
|
0
|
324
|
April 1, 2021
|
|
Press Z- or Z+for a long time(about 3~4s),the Z axis will always go down/up;Press the short time is noraml
|
|
0
|
278
|
April 1, 2021
|
|
How to install the USB drive
|
|
0
|
405
|
March 31, 2021
|
|
CCD software "take pictures in advance" problem
|
|
0
|
241
|
March 31, 2021
|
|
The floodlight of the camera is not bright
|
|
0
|
277
|
March 31, 2021
|
|
Incompatible flie formats
|
|
0
|
282
|
March 31, 2021
|
|
The scanned figure is uneven at the bottom
|
|
0
|
290
|
March 31, 2021
|
|
"Flie incompatibility" in RDC6442
|
|
0
|
279
|
March 31, 2021
|
|
The problem with the parameters setting for V6342
|
|
0
|
266
|
March 30, 2021
|
|
The depth of cutting or engrving is not enough
|
|
0
|
290
|
March 30, 2021
|
|
The bottom is uneven when carving
|
|
0
|
258
|
March 30, 2021
|
|
When starting the reset,the shaft has been touching the voltage limit switch
|
|
0
|
297
|
March 30, 2021
|
|
Do not know how to upgrade file
|
|
0
|
254
|
March 30, 2021
|
|
The panel cannot cnnnect to the device
|
|
0
|
265
|
March 30, 2021
|
|
Trying to cut a squre results in a parallelogram
|
|
0
|
264
|
March 30, 2021
|