|
Machine selection problems in the diamond cutting machine and vision-based diamond analyzer industry
|
|
0
|
321
|
April 20, 2021
|
|
The difference between P100mx and p100q raycus laser
|
|
0
|
324
|
April 20, 2021
|
|
Cutting will cause problems in the picture
|
|
0
|
343
|
April 20, 2021
|
|
No rotating shaft, if you want to add a rotating shaft, how to connect it
|
|
0
|
409
|
April 20, 2021
|
|
Optical fiber marking machine LiteMarker, the problem in the picture appears when marking
|
|
0
|
359
|
April 20, 2021
|
|
The optical fiber marking machine has the problem as shown in the figure, how to solve it
|
|
0
|
375
|
April 20, 2021
|
|
EM-Smart laser marking machine cannot install the driver
|
|
0
|
502
|
April 20, 2021
|
|
Replace a large wattage machine
|
|
0
|
312
|
April 20, 2021
|
|
The MAX 50W fiber laser does not emit light
|
|
0
|
390
|
April 20, 2021
|
|
The machine does not have enough space to use the rotating shaft
|
|
0
|
373
|
April 20, 2021
|
|
30W split marking machine, the LED light on the machine does not light up, is there a replacement?
|
|
0
|
372
|
April 19, 2021
|
|
Ruida controller can not reset automaticlly when power on
|
|
0
|
349
|
April 19, 2021
|
|
Z axis does not work in RDC6445G
|
|
0
|
529
|
April 19, 2021
|
|
After FSCUT2000C is turned on, the display system does not support it, and it can only be run in demo mode
|
|
0
|
393
|
April 19, 2021
|
|
I bought 6442S instead of 6445G, what should I do if the XY axis direction is reversed
|
|
0
|
333
|
April 19, 2021
|
|
Password of Ruida mainboard
|
|
0
|
481
|
April 19, 2021
|
|
M5-BOX Laser Manual for the MAX photonics
|
|
0
|
543
|
April 19, 2021
|
|
JCZ Fiber Streamlined Cassette Reel, I tried WIN10 and 7 system can’t recognize USB
|
|
0
|
381
|
April 17, 2021
|
|
Adaptation software and communication method of JCZ digital compact card
|
|
0
|
360
|
April 17, 2021
|
|
Can the 6445 panel be used with the 6442S motherboard
|
|
0
|
343
|
April 17, 2021
|
|
HYZ100 power supply is connected with 6445G, why there is no display on the panel
|
|
0
|
367
|
April 17, 2021
|
|
The X axis of the main control board RDLC320-A does not work, how to troubleshoot
|
|
0
|
357
|
April 16, 2021
|
|
How to prove that the 24v port of the CN1 interface of the controller can work normally
|
|
0
|
339
|
April 16, 2021
|
|
The L and P indicators on the power supply are both off. Is it broken
|
|
0
|
317
|
April 16, 2021
|
|
MYJG150W, everything is normal, all connections are correct, but if you try to make a complete grating engraving, even if the power is reduced to a minimum, it will become too deep and can only be cut
|
|
0
|
332
|
April 16, 2021
|
|
The power supply device makes a huge noise and malfunctions and causes the laser to emit (pulse) by itself, which is very dangerous. It can also work when the power is turned on. Power DY13
|
|
0
|
344
|
April 16, 2021
|
|
Continuous discharge of power supply
|
|
0
|
356
|
April 16, 2021
|
|
Need a laser tube in which a transparent window is installed instead of a resonator mirror
|
|
0
|
320
|
April 16, 2021
|
|
The laser tube emits pink light, no output, and it is impossible to mark the paper in front of the light outlet. Is this laser tube broken?
|
|
0
|
315
|
April 16, 2021
|
|
Low frequency use of laser tubes in cold areas
|
|
0
|
334
|
April 16, 2021
|