# Scan rate isn't fast. 2000mm/s is about the same as 300mm/s

**URL:** <https://forum.cloudray.com/t/scan-rate-isnt-fast-2000mm-s-is-about-the-same-as-300mm-s/1043>\
**Category:** Pre-sales & After-sales\
**Created:** [February 2, 2023, 5:25pm UTC](https://forum.cloudray.com/t/scan-rate-isnt-fast-2000mm-s-is-about-the-same-as-300mm-s/1043 "2023-02-02T17:25:00Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![jkwilborn](https://sea2.discourse-cdn.com/flex020/user_avatar/forum.cloudray.com/jkwilborn/32/687_2.png) [@jkwilborn](https://forum.cloudray.com/u/jkwilborn)\
**Post date:** [February 2, 2023, 5:25pm UTC](https://forum.cloudray.com/t/scan-rate-isnt-fast-2000mm-s-is-about-the-same-as-300mm-s/1043/1 "2023-02-02T17:25:00Z")

</div>

I run Lightburn and received my MP-60 yesterday. It seems to be operating, but the scan speed is not responding as expected.

300mm/s was used to initially test. When I increased the rate to 1000 there was little to no visual difference and the actual execution time of the layer took the same amount of time.

Tried up to 4000mm/s, but no change in time or visual difference.

I assume it’s software as the image is correct …

* * *

I don’t seem to see anything that limits this in the software, is there?

Is there a way to check these speeds? I’d like to confirm I do have a problem…

Thanks

Jack Wilborn

---

<div class="post-metadata">

**Author:** ![lucas](https://avatars.discourse-cdn.com/v4/letter/l/ba8739/32.png) [@lucas](https://forum.cloudray.com/u/lucas)\
**Post date:** [February 3, 2023, 2:28am UTC](https://forum.cloudray.com/t/scan-rate-isnt-fast-2000mm-s-is-about-the-same-as-300mm-s/1043/2 "2023-02-03T02:28:36Z")

</div>

Can you share all your parameter settings?

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://sea2.discourse-cdn.com/flex020/user_avatar/forum.cloudray.com/jkwilborn/32/687_2.png) [@jkwilborn](https://forum.cloudray.com/u/jkwilborn)\
**Post date:** [February 3, 2023, 1:15pm UTC](https://forum.cloudray.com/t/scan-rate-isnt-fast-2000mm-s-is-about-the-same-as-300mm-s/1043/3 "2023-02-03T13:15:46Z")

</div>

I assume this was populated by the EZCad2 file markcfg7 that was on the memory stick that came with the machine. Lightburn imported it when I created the device.

I have changed the scale for both x and y as the square was larger than it should have been. I also changed the min/max frequencies, based on the JPT MOPA manual entry of 40 to 4000 kHz.

 ![lightburn-settings](https://us1.discourse-cdn.com/flex020/uploads/cloudray/original/1X/085e43a5d4a94a4c7b0c41001dac9e6ff4b7c047.png)

EDIT: will mark this as solved (that I can’t find)… The timings are showing that it’s working… Sorry for any confusion…

Thanks

Jack Wilborn

😺
